shielded power inductors C mss6132 document 641-1 document 641-1 revised 09/02/15 designers kit c364 contains 3 of each value core material ferrite core and winding loss see www.coilcraft.com/coreloss terminations rohs compliant matte tin over nickel over phos bronze (current production) or gold over nickel over phos bronze (prior production). other terminations available at additional cost. weight 0.33 C 0.38 g ambient temperature C40c to +85c with (40c rise) i rms current. maximum part temperature +125c (ambient + temp rise). derating . storage temperature component: C40c to +125c. tape and reel packaging: C40c to +80c resistance to soldering heat max three 40 second refows at +260c, parts cooled to room temperature between cycles moisture sensitivity level (msl) 1 (unlimited foor life at <30c / 85% relative humidity) failures in time (fit) / mean time between failures (mtbf) 38 per billion hours / 26,315,789 hours, calculated per telcordia sr-332 packaging 500/7 reel, 1500/13 reel; plastic tape: 16 mm wide, 0.3 mm thick, 12 mm pocket spacing, 3.1 mm pocket depth pcb washing tested to mil-std-202 method 215 plus an additional aqueous wash. see doc787_pcb_washing.pdf . dcr srf i sat (a) 4 i rms (a) 5 inductance 2 max typ 3 10% 20% 30% 20c 40c part number 1 20% (h) (ohms) (mhz) drop drop drop rise rise mss6132-472ml_ 4.7 0.043 65.0 2.18 2.60 2.84 2.30 3.10 MSS6132-562ML_ 5.6 0.048 60.0 2.10 2.50 2.74 2.20 2.95 mss6132-682ml_ 6.8 0.052 47.0 1.80 2.12 2.30 2.10 2.80 mss6132-822ml_ 8.2 0.055 45.0 1.78 2.06 2.22 2.00 2.65 mss6132-103ml_ 10 0.070 39.0 1.36 1.64 1.84 1.90 2.50 mss6132-123ml_ 12 0.079 33.0 1.30 1.54 1.70 1.75 2.35 mss6132-153ml_ 15 0.106 27.0 1.16 1.42 1.56 1.65 2.20 mss6132-183ml_ 18 0.118 24.0 1.04 1.22 1.36 1.55 2.05 mss6132-223ml_ 22 0.158 21.0 0.97 1.12 1.22 1.45 1.90 mss6132-273ml_ 27 0.180 19.0 0.91 1.08 1.18 1.30 1.75 mss6132-333ml_ 33 0.250 18.0 0.81 0.96 1.10 1.20 1.60 mss6132-393ml_ 39 0.275 17.0 0.79 0.92 0.99 1.10 1.45 mss6132-473ml_ 47 0.300 16.0 0.72 0.86 0.93 0.95 1.30 mss6132-563ml_ 56 0.380 14.0 0.61 0.72 0.79 0.85 1.15 mss6132-683ml_ 68 0.410 12.0 0.55 0.63 0.69 0.73 1.00 mss6132-823ml_ 82 0.510 10.0 0.53 0.62 0.67 0.60 0.85 mss6132-104ml_ 100 0.660 9.0 0.45 0.54 0.59 0.50 0.69 ? 6.1 6.1 mm footprint; 3.2 mm high shielded inductors ? low dcr and excellent current handling 1. please specify termination and packaging codes: mss6132-823m lc termination: l = rohs compliant matte tin over nickel over phos bronze (current production) or gold over nickel over phos bronze (prior production) special order: t = rohs tin-silver-copper (95.5/4/0.5) over gold over nickel over phos bronze or s = non-rohs tin-lead (63/37) over gold over nickel over phos bronze. packaging: c = 7 machine-ready reel eia-481 embossed plastic tape (500 per full reel). b = less than full reel in tape, but not machine-ready. to have a lead - er and trailer added ($25 charge), use code letter c instead. d = 13 machine-ready reel eia-481 embossed plastic tape. factory order only, not stocked (1500 per reel per full reel). 2. inductance tested at 100 khz, 0.1 vrms, 0 adc using an agilent/hp 4263b lcr meter or equivalent. 3. srf measured using agilent/hp 4191a or equilvalent. 4. dc current at which the inductance drops the specifed amount from its value without current. 5. dc current at 25c that causes the specifed inductance drop from its value without current. click for temperature derating information . 6. current that causes the specifed temperature rise from 25c ambient. this information is for reference only and does not represent absolute maximum ratings. click for temperature derating information . 7. electrical specifcations at 25c. refer to doc 362 soldering surface mount components before soldering.
document 641-2 smt power inductors C mss6132 0.01 0.1 11 0 current (a) 1 10 100 1000 inductance (h) 100 h 4.7 h 22 h typical l vs current typical l vs frequency 0.01 0.1 11 0 frequency (mhz) 10 1 100 1000 inductance (h) 1 00 h 22 h 4.7 h dimensions are in inches mm 0.220 5,6 0.220 5,6 0.079 2,0 0.240 6,1 0.240 6,1 123 * * * dimensions are of the case not including the ter mination. fo r maximum ov erall dimensions including the ter mination, add 0.016 in / 0,4 mm. 0.237 6,0 0.237 6,0 min recommended land p attern 0.079 2,0 0.191 4,85 f 0.112 0.014 2,85 0,35 dash n umber document 641-2 revised 09/02/15
|
